Crude Oil Production

Current data on crude oil, field/lease condensate, and natural gas liquids produced from NGL plants. Updated on a monthly basis.     

积分中值屈服准则解析厚板轧制椭圆速度场

为解决非线性Mises比塑性功率积分困难以及由此导致的轧制功率解析式难以获得的问题,本文通过建立并利用线性比塑性功率表达式对提出的椭圆速度场进行能量分析,得到了轧制力能参数的解析解.文中通过对变角度屈服函数求积分中值,构建了一个新的屈服准则,它是主应力分量的线性组合,在π平面上的轨迹是逼近Mises圆的等边非等角的十二边形,其基于Lode参数表达式的理论结果也与实验数据吻合较好.同时,根据厚板轧制时金属流动速度从入口到出口逐渐增大的特点,提出了水平速度分量满足椭圆方程的速度场,该速度场满足运动许可条件.通过相应的轧制能量分析,获得了基于线性屈服准则的内部变形功率以及基于应变矢量内积法上的摩擦功率与剪切功率.在此之上,通过泛函的极值变分导出了轧制力矩、轧制力以及应力状态系数的解析解,并与现场实测数据进行了对比,结果表明利用本文提出的屈服准则与速度场所建立的轧制力矩与轧制力模型与实测值吻合较好,其中轧制力误差小于5.3%,轧制力矩误差在6%左右.     

退火温度对6.5%Si极薄带织构及磁性能的影响

采用单辊甩带法制备了厚度为0.03 mm的6.5%Si极薄带,并在真空炉中进行了880 ℃和920 ℃的退火处理。利用XRD和EBSD研究了其在退火后的宏观和微观织构演变规律。结果表明:经单辊甩带制得的6.5%Si极薄带织构主要由{001}<100>立方织构、{110}<001> Goss织构和{112}<111>织构组成。随着退火温度的升高,λ纤维仍占主导地位,且晶粒尺寸逐渐增大。特别是在920 ℃退火时,{001}<120>和{001}<100>晶粒的尺寸优势逐渐增大,不利织构{111}<110>和{111}<112>逐渐减弱,且最终的磁感应强度B₅₀=1.644 T,铁损耗P_10/400=5.896 W/kg。     

某铜矿重介质产品提铁降硫选矿试验

某铜矿重介质产品铁品位56.24%，硫含量高达9.34%，95.72%的硫以磁黄铁矿的形式存在。为获得硫含量<2%的铁精矿，按磨矿—弱磁选—浮选原则流程对该矿石进行了选矿试验。试验结果表明，在最佳试验参数下，重介质产品经一段磨矿（-0.043 mm 85%）—1粗1精弱磁选—1粗2扫脱硫浮选流程处理，可获得产率45.23%、硫含量为1.52%、全铁品位66.50%的铁精矿，可作为后续钢铁冶炼原料的配矿使用，为此类重介质产品的利用提供技术参考。     

Thermal and hydraulic characteristics of a large-scaled parabolic trough solar field (PTSF) under cloud passages

To better understand the characteristics of a large-scaled parabolic trough solar field (PTSF) under cloud passages, a novel method which combines a closed-loop thermal hydraulic model (CLTHM) and cloud vector (CV) is developed. Besides, the CLTHM is established and validated based on a pilot plant. Moreover, some key parameters which are used to characterize a typical PTSF and CV are presented for further simulation. Furthermore, two sets of results simulated by the CLTHM are compared and discussed. One set deals with cloud passages by the CV, while the other by the traditionally distributed weather stations (DWSs). Because of considering the solar irradiance distribution in a more detailed and realistically way, compared with the distributed weather station (DWS) simulation, all essential parameters, such as the total flowrate, flow distribution, outlet temperature, thermal and exergetic efficiency, and exergetic destruction tend to be more precise and smoother in the CV simulation. For example, for the runner outlet temperature, which is the most crucial parameter for a running PTSF, the maximum relative error reaches −15% in the comparison. In addition, the mechanism of thermal and hydraulic unbalance caused by cloud passages are explained based on the simulation.     

磁性石墨烯/聚氨酯柔性复合材料的制备及自修复效能

为了提高复合材料的导电、导热及自修复性能，在传统共混法的基础上采用化学沉积法将四氧化三铁（Fe₃O₄）修饰到石墨烯上，得到磁性石墨烯，并将其与聚氨酯、碳纳米管共混后经磁场干预控制石墨烯片层的排列得到磁性石墨烯/聚氨酯柔性复合材料。采用SEM、Raman、FTIR对柔性复合材料的微观形貌、分子结构进行表征，并通过激光导热仪、四探针电阻率测定仪和万能试验机分析磁场调控对复合材料电、热、力学以及修复性能的影响。结果表明：磁场下柔性复合材料中的石墨烯片层排列规则，且层次分明，轮廓清晰可见；其热扩散系数相比于未加磁场提高了10 %~12 %，且在高温下具有稳定性，缺陷修复时间减少了50 %；对比出现缺陷前及修复后的复合材料发现，表面电阻率和抗拉强度分别相差0.006Ω·cm和2.4MPa，而无磁场环境下的变化量是其 3～4倍。     

机械密封腔流场内粒子对密封腔壁面及波纹管冲蚀分析

为研究机械密封腔内混有固体颗粒的流体,在复杂工况下对密封腔壁面及波纹管表面冲蚀的影响,以CFD理论及方法,采用k-ε湍流模型和离散项DPM模型,对固液混合流场进行模拟分析,获得密封腔内流体中介质作用下密封腔壁面及波纹管外表面的压力场分布,分析不同工作状态下固体颗粒作用下密封腔内壁和波纹管外表面的冲蚀区域分布、固体颗粒在流场中的运动轨迹,以及机械密封工作过程中流场内固体颗粒的逃逸量、运动状态的变化。结果表明:粒子主要受颗粒阻力、浮重力、压力梯度力及波纹管和密封腔表面反作用力的影响;在旋转流场中,粒子作与旋转方向一致的螺旋方式前进;无转速时,冲蚀多发生在靠近入口处的波纹管外表面,旋转流场中,冲蚀多发生在密封腔靠后位置的壁面;随着转速增加,粒子逃逸率下降。研究结论为机械密封腔的设计布局及机械密封装置的优化提供理论依据。     

相场法模拟GaAs衬底上InGaAs异质结表面形貌

本工作采用相场法模拟GaAs衬底上生长的In_(0.3)Ga_(0.7)As多层异质结构薄膜表面。通过引入多序参量,使用半隐性傅里叶谱方法求解Cahn-Hilliard方程可以求得带缓冲层结构的薄膜表面形貌。计算结果模拟了薄膜生长过程,研究显示,使用In0.15-Ga0.85As缓冲层,厚度从1nm增加到4nm,薄膜表面临界波长从34nm提升到80nm。随着缓冲层的厚度从1nm增加到10nm,使用正弦波表面的模拟结果显示,薄膜表面粗糙度从2.87nm下降到0.43nm,随机叠加波表面的模拟结果也类似,表面粗糙度从1.21nm下降到0.18nm。热力学分析和应变分布分析可以解释缓冲层对薄膜表面形貌演化的作用。该模拟计算方式对设计缓冲层结构有很大的帮助,模拟计算的结果可以与实验相比对。     

The efficiency and comparison of novel techniques for cell wall disruption in astaxanthin extraction from Haematococcus pluvialis

The efficiency of various techniques pulsed electric field (PEF), ultrasound (US), high‐pressure microfluidisation (HPMF), hydrochloric acid (HCl) and ionic liquids (ILs) for cell wall disruption in astaxanthin extraction from Haematococcus pluvialis was compared. The results indicated that ILs, HCl and HPMF treatment were shown the most efficient for cell disruption with more than 80% astaxanthin recovery. While the cell wall integrity of H. pluvialis cyst cell was less affected by US and PEF treatment. It was found that imidazolium‐based ILs showed the greater potential for cell disruption than pyridinium‐based and ammonium‐based ILs. Among all the ILs examined, 1‐butyl‐3‐methylimidazolium chloride ([Bmim] Cl) exhibited efficient cell disruption and capability of astaxanthin recovery at mild condition (pretreatment with 40% IL aqueous solution at 40 °C, followed by extraction with methanol at 50 °C) without extensive energy consumption and special facility requirement. In addition, recyclability of ILs was excellent.